Dura vent stove pipe installation

Or is the double wall designed to allow air to enter there? I have to tried just setting the pipe right on the collar. I thought the adapter was supposed to make this easy. Click to expand Just not sure if that adapter is supposed to be flush with the top of the stove.

Maybe that ok. I have no idea. If you look at my last picture, that little metal lip right above the crimped section is what is stopping the adapter on the collar. I like the corner look so I really wanted to try to get that offset.

Draft is great. Fired her up last night and enjoyed some toasty warmth. Reactions: BoilerBob and webby You must log in or register to reply here. Similar threads M. For horizontal installations, check the appliance manufacturer's instructions for minimum rise and maximum horizontal run. A snorkel termination may be used if height restrictions prevent adequate rise above the appliance.

Select the appropriate Horizontal Termination Cap see appliance manufacturer installation instructions. To protect vinyl siding, select vinyl siding standoff. Check appliance manufacturer's instructions for wall thimble and firestop requirements. The following design recommendations are intended as only a general guideline to assist in the design and selection of venting components for your installation.

Always read and follow Simpson Dura-Vent Installation instructions enclosed with the cap or support box before installing your chimney system. Installation instructions can be viewed on the item page on our website. Important: Check the manufacturer's rating plate and instruction manual to confirm that the Simpson Dura-Vent direct vent system is approved for use on the brand name appliance you have selected.

He is a Master Hearth Professional, which means he is certified in all three hearth appliance fields—wood, gas and pellet. When not at work, he spends time with his wife, Lindsey, and his sons, Samuel and Eli, on their ranch enjoying their many animals. Completing projects around the ranch and spending quality time with his family are among his greatest joys. My Account Order Status Help. Shop By Brand. View All. Shop Vented Log Styles.

Shop Ventless Log Styles. Shop By Type. Shop By Use. BY Collin Champagne A Wall Thimble must be installed with an appropriate section of chimney pipe for all horizontal through-the-wall installations. To accommodate thicker walls a wall thimble extension can be field fabricated.

An Attic Insulation Shield must be used in all installations that pass through an attic, regardless of whether the attic is insulated or not. If chimney is enclosed in a chase in the attic space, an Attic Insulation Shield is not required. A Firestop Radiation Shield must be used when a chimney passes through a floor or ceiling without a Ceiling Support Box.

Planning Your Installation The following recommendations are intended as a general guideline to assist in the layout and selection of the chimney components needed for your installation. The diameter of the chimney should match the outlet size of the appliance. An improperly sized chimney results in poor draft and excessive creosote formation. Measure the diameter of the appliance flue outlet. Select the chimney and either DVL or DuraBlack connector stovepipe with the same size diameter as the appliance flue outlet.

For fireplace installations, refer to the sizing chart in the back of this catalog. Determine if the installation is a through-the-roof installation or a through-the-wall installation. Install the chimney in the interior of the structure whenever possible. A cold exterior chimney will produce less draft and will generate more creosote. If possible, avoid offsets that serve to restrict the natural draft.

A straight vertical installation is more efficient and less likely to develop creosote. If an offset is required to avoid rafters or other obstructions, measure the horizontal distance required and the vertical height available.

A maximum of two offsets in a single installation are permitted. Refer to the offset table in the back of this catalog. Primary metal-to-metal connection seals joint. Encapsulated o-ring provides a secondary seal. Information available online at www. Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation. The following design recommendations are a general guideline to assist in the design and selection of venting components for your installation.

Always follow DuraVent Installation instructions before installing your chimney system found with the cap or support box. All PelletVent Pro components that come into contact with flue gases are built with an inner wall of corrosion resistant superferritic metal.